Cooling towers are heat rejection devices which reject waste heat to the atmosphere via the cooling of a water stream in order to lower temperature.
And if you have never worked in a cooling tower before then you might think that the heart of any cooling towers is the water itself. Although the main purpose of any cooling tower does revolve around water, the true heart of every cooling tower is its fills. We can help get different pvc fills for cooling tower.
Wholesale High Strength Heat Resistant PVC Cooling Tower Fill
Cooling tower filling, also named as cooling tower fill media, or cooling tower fill pack, or cooling tower infill, or cooling tower filler, is made of PVC or PP plain plate, hot pressed in a certain mould and produced with different designs and sizes.
Cooling tower fill is a very important component for water and gas exchanging in cooling towers. It is located in the middle or bottom of the cooling tower. Some cooling towers would be full of the fill media, some would have half and half of the fill media, and some large cooling towers would be installed 1 layer of the fill media in the bottom.
Specification
| Model |
ML |
| Material |
PP, PVC |
| Width |
610mm, 750mm, 813mm, 915mm, 1000mm, 1220mm, 1520mm |
| Length |
1854mm, 2060mm, 2450mm, 2678mm, 2980mm, 3090mm |
| Thickness |
0.30mm ~ 0.45mm |
| Pitch |
19mm ~ 20mm |
| Sample |
Available |
| Customization |
Accepted |
MX cooling tower fill is available in MX75 configuration and higher-performing MX625 configuration. MX is a hanging film type cooling tower fill which spreads the water into a thin film, flowing over large vertical surfaces, promoting maximum exposure to air flow. This type of fill provides much more water surface exposure per cubic foot than splash type fill.
MX fill incorporates highly efficient cellular drift eliminators, integrally molded within the fill sheets. Compared with previous designs, these eliminators reduce drift emissions from the tower by a factor of ten or more! Less drift means tower owners save water bills and water treatment chemical expenses.
This fill virtually eliminates the nuisance caused by drift spotting on adjacent buildings and property. For additional savings, the drift eliminators discharge air directly toward the fan. Discharge air, traveling in the right direction when it leaves the eliminators, translates to lower fan horsepower.
MX fill is thermoformed from PVC with a flame spread rating less than 25 per ASTM E-84 and is considered selfextinguishing. Therefore, the risk of fire damage is minimal.
Feature
1. Cooling Tower fill has the good characteristic of hydrophilicity, proof-oil, high-temperature-resistant, it doesn't occur geometric alteration under condition of 65°C, and it won't crash and crack under condition of -40°C. Its anti-flaming oxygen index is more than 40.
2. According to practically experience of similary project, the filling is bound by special adhesive, ratio of bonding is no less than 95%, intensity of flat crushing ≥3000 N/m2, shear intensity after being bound for 24 hours is more than 3.3Mpa.
3. Cooling Tower fill has the good characteristic of hydrophilicity, proof-oil, high-temperature- resistant, anti-ageing. The strength of filling block is more than 300Kg/m2.
Application
Industrial water cooling
Air compressor
Aluminum profile processing
Steam turbine
Power generation
Tannery
Electric furnace
Freezing Series
Air conditioning cooling system
Package and Delivery
To better ensure the safety of your goods, professional, environmentally friendly, convenient and efficient packaging services would be provided.
Usually cooling tower fills are packed with pallet or wooden case.
Related Products
Our Service
We offer professional products and fast delivery.
We will help you solve problems when you use our products.
Any question, you can turn to the technology department of our company.
- Fast delivery (Our factory has high production capacity and there is enough inventory to insure fast delivery for you).
- Competitive price (We are the original manuafacturer of our products, so we can provide you both high quality products and competitive price).
- Quick response for each inquiry within 24hours.
- Quality control strickly.
- Quick delivery to imporve your effciency.
FAQ
1. Q: Are you a Trading Company or Factory?
A: We are a factory with export certificate.
2. Q: What's your production ability for one month?
A: We can produce 50000 square meters per month.
3. Q: What's your MOQ?
A: 1000 square meters.
4. Q: What's your shipping port?
A: Tianjin, Shanghai or any port as your request.
5.Q: What's your Payment Term?
A: L/C, T/T, Western Union.
Try order is acceptable. Sample is available.
Welcome your inquiry, we will give feedback within 24 hours.
){kind=link}
){kind=link}